Conversión de un aporte oxiacetilénico R-FeCr en E-FeCr para recubrimiento de piezas sometidas a desgaste erosivo

Eduardo Díaz-Cedré, Amado Cruz-Crespo, Americo Scotti, Alexis García-Hernández, Jorge Víctor Miguel-Oria, Nancy M. Pérez-Pino

Resumen


Se estudió la conversión de un aporte oxiacetilénico R-FeCr en un aporte por arco eléctrico E-FeCr, para el relleno manual de piezas sometidas a desgaste erosivo (tornillos extrusores de arcilla), con la finalidad de incrementar la productividad de los procesos de relleno superficial y disminuir deformaciones sin reducir las propiedades de los depósitos. Se partió de la formulación de un revestimiento bajo hidrógeno, ensayado en trabajos previos, el cual fue aplicado por inmersión. Se realizaron depósitos mediante un simulador que permite realizar ensayos de soldadura manual sin la interferencia directa del soldador, variando la corriente de soldadura. Se determinaron las características técnico–operativas (tasa de fusión, tasa de deposición, rendimiento real, estabilidad de funcionamiento, metalografía y dureza del depósito) de los consumibles en estudio. El análisis de estas características permitió demostrar la factibilidad técnica de esta conversión.

Palabras clave


Desgaste erosivo; recubrimiento; SMAW; comportamiento operacional; microestructura

Texto completo:

PDF

Referencias


AMERICAN SOCIETY FOR METAL. 1992: Friction, Lubrication, and Wear Technology. Volume 18, ASM International, 1 879 p.

AMERICAN WELDING SOCIETY. 2002: A5.13 Specifications for Surfacing Welds Rods and Electrodes., 22 p.

BRANDI, S. D.; TANIGUCHI, C. & LIU, S. 1991: Analysis of Metal Transfer in Shielded Metal Arc Welding. Welding Journal, October: 261-270.

BUCHELY, M. F.; GUTIÉRREZ, J. C.; LEÓN, L. M. & TORO, A. 2006: The effect of microstructure on abrasive wear of hardfacing alloys. Wear 259: 52-61.

CARY, H. B. 1994: Modern Welding Tecnology. Third Edition. Regents/Prentice Hall, New York, 800 p.

COELHO, A. & FERRARESI, A. 2009: Análise da Microestrutura e da Resistência al Desgaste de Revestimento Duro Utilizado pela Indústria Sucroalcooleira. Soldagem & Inspecao 14(2): 140-150.

CRUZ-CRESPO, A.; FERNÁNDEZ-FUENTES, R. & SCOTTI, A. 2009: The Influence of Calcite, Fluorite, and Rutile on the Fusion-Related Behavior of Metal Cored Coated Electrodes for Hardfacing. Journal of Materials Engineering and Performance 32(Sept): 41-47.

CRUZ-CRESPO, A.; PERDOMO, L.; PÉREZ, M. R.; FERNÁNDEZ, R. & ORTIZ, T. M. 2006: Obtención de un fundente aglomerado aleado y un electrodo tubular revestido con el empleo de FeCrMn y escoria de la reducción carbotérmica de minerales. En: Congreso da Sociedade Brasileira de Soldagem. Belo Horizonte, Brasil, octubre, 26-32.

CRUZ-CRESPO, A.; SCOTTI, A. & RODRÍGUEZ-PÉREZ, M. 2008: Operational behavior assesment of coated tubular electrodes for SMAW hardfacing. Journal of Materials Processing Technology 199: 265-273.

DA, L.; LIGANG, L.; YUNKUN, Z.; CHUNLEI, Y.; XUEJUN, R.; YULIN, Y. & QINGXIANG, Y. 2009: Phase diagram calculation of high chromium cast irons and influence of its chemical composition. Materials and Design 30: 340-345.

DE MELO, R. & VILLANI-MARQUES, P. 2009: Estudo Comparativo da Resistência ao Desgaste Abrasivo do Revestimento de Três Ligas Metálicas Utilizadas na Indústria, Aplicadas por Soldagem com Arames Tubulares. Soldagem & Inspeccao 14(4), Out/Dez: 329-335.

FARIAS, J. P.; BÁLSAMO, P. S. & SURIAN, E. S. 2004: The effect of wollastonite on operational characteristics of AWS E6013 electrodes. Journal of the Brazilian Society of Mechanical Sciences and Engineering 26(3): 17-21.

FERNÁNDEZ, J. E.; VIJANDE, R.; TUCHO, R.; RODRÍGUEZ, J. & MARTÍN, A. 2001: Materials selection to excavator teeth in mining industry. Wear 250: 11-18.

GULENC, B. & KAHRAMAN, N. 2003: Wear behaviour of bulldozer rollers welded using a submerged arc welding process. Materials and Design 24: 537-542.

LINCOLN ELECTRIC COMPANY. 2000: The Procedure Handbook of Arc Welding. Cleveland, Ohio, 783 p.

MARTÍNEZ-PRIETO, F. & MARTÍNEZ-ESCANAVERINO, F. 1997: Teoría y Práctica del Rozamiento. Editorial CUJAE, La Habana, 243 p.

MAZEL, Y. A. 2006: Development of high-productivity high-alloyed electrodes. Welding International 20(11): 913-917.

REHFELDT, D. & BOLLMAN, A. 1987: Comparing Investigations of Covered Electrodes of Different Fabrications by Statistical Process Analysis’. IIW Documet 212-677-87.

SCOTTS, W. 1984: Proceedings of the International Conference on Tribology in Mineral Extraction. Nottingham, UK, 4-8 October, 45-52.

SHARMA, B. C. 2006: Process Stability Evaluation of Basic Coated Manual Metal Arc Welding Electrodes. Journal of the Institution of Engineers (India) 86(March): 39-48.

SOUZA, M. S.; GADOTTI, I. & SCOTTI, A. 1995: Um Banco de Ensaio para Avaliar Eletrodos Revestidos. En: XIII Congreso Brasileiro de Engenharia Mecânica – COBEM - II Congreso Ibero Americano de Engenharia Mecânica – CIDIM. Belo Horizonte, Brasil, 6-8 Dez, p. 62-69.

YAROVCHUK, A. V. 2005: Effect of ferrochrome content on the oxidation-reduction processes in welding slags based on titanium dioxide. Welding International 8: 651-656.


Estadísticas

Resumen
373
PDF
96


Copyright (c) 2013 Eduardo Díaz-Cedré, Amado Cruz-Crespo, Americo Scotti, Alexis García-Hernández, Jorge Víctor Miguel-Oria, Nancy M. Pérez-Pino

Licencia de Creative Commons
Este obra está bajo una licencia de Creative Commons Reconocimiento-NoComercial 4.0 Internacional.