Qualification of microconstituents or metallographic phases of an ASTM A 36 steel welded with a shield electrode
Keywords:
digital processing of images, microconstituents, phase, pixel.Abstract
The microconstituents in a butt welded ASTM A 36 steel with edge preparation by means of electric arc welding with electrode E 7018 were quantified through digital image processing. Samples with bevels of 30 and 35o were prepared, which were called MI for the former and MII for the latter. The phases, the grain boundaries and the area present in the microstructure of this steel visualized in an element called pixel were identified. It was determined that, in the molten zone and in the zone affected by heat for the 30o bevel, the phase that predominates is pearlitic with 82.25%, which occupies the greatest distribution over the area of the matrix and in that of 35th, there is a tendency to remain the same, but with 56.82%; which is associated with the heat input due to the effect of the thermal cycle and the type of angle used.Downloads
References
ABEDI, S. 2017. Investigación de falla de una soldadura defectuosa de una tubería de transmission de productos petrolíferos. Revista de análisis y prevención de fallas 17(1): 30-37.
ADAK, D.; MUKHERJEE, M.; PAL, T. 2015. Development of a direct correlation of bead geometry, grain size and HAZ width with the GMAW process parameters on bead-on-plate welds of mild steel. Transaction of the Indian Institute of metals 68(9): 839-849.
ASKELAND, D.; FULAY, P. & WRIGHT, W. 2013. Introducción a la ciencia e ingeniería de materiales. In Ciencia e ingeniería de los materiales, 3rd ed., J. Hernández, Ed. México: CIENGAGE Learning, pp. 3–22.
ASTM 1996. International, Standard Test Methods for Determining Average Grain Size, p. 2.
BHATTI, A.; BARSOUM, Z.; MURAKAWA, H.; BARSOUM, I. 2015. Influence of thermomechanical material properties of different steel grades on welding residual stresses and angular distortion. Materials and Design 65(5): 878-889.
BURGE, M. & BURGER, W. 2016. Digital image processing, 2nd ed. New York: Springer International Publishing.
FRIELD, J. 2000. Principles of Image Analysis, in Practical Guide to Image Analysis. 1st ed., United States of America: ASM International, pp. 75–101.
KANG, J & PARK, C. 2008. Characterization of bainitic microstructures in low carbon hsla steels. International Journal of Modern Physics B. 22(31): 5965-5970.
JUNG, G. & TSAI, C. 2004. Plasticity-based distortion analysis for fillet welded thin-plate t-joints. Welding Journal 83(6): 177-187.
KOCH, D.; DESPOTOVIC, M.; LEIBER S.; SAKEENA, M.; DÖLLER, M. Y ZEPPELZAUR, M. 2019. Análisis de la imagen inmobiliaria: una revision de la literature. Revista de literature inmobiliaria 27(2): 269-300.
NASCIMENTO-NGACA, A. & FERNÁNDEZ COLUMBIÉ, T. 2021. Influencia del ángulo de bisel en la soldadura a tope de un acero ASTM A 36 soldado con electrodo revestido. Ciencia & Futuro 11(3): 36-47.
SURESH-KUMAR, K. 2014. Analytical modeling of temperature distribution, peak temperature, cooling rate and thermal cycles in a solid works piece welded by laser welding process. Procedia Materials Science 6(1): 821-834.
XIONG, J. 2014. Bead geometry prediction for robotic GMAW based rapid manufacturing through a neural network and a second-order regression analysis. USA: Springer Science+Business Media. 25(5): 157-163.
ZHANG, Y. 2017. Introduction to Image Analysis, in Image Engineering, Volume II: Image Analysis, 1st ed., Beijing: DE GRUYTER, pp. 1–25.
Published
How to Cite
Issue
Section
Esta obra está bajo una Licencia Creative Commons Reconocimiento-NoComercial 4.0 Internacional
La Revista Ciencia & Futuro es una revista de acceso abierto, todo el contenido está disponible gratuitamente sin cargo para el usuario o su institución. Los usuarios pueden leer, descargar, copiar, distribuir, imprimir, buscar o vincular los textos completos de los artículos, o utilizarlos para cualquier otro fin lícito, sin pedir permiso previo al editor o al autor. Todo lo anterior, de acuerdo con la definición de BOAI de acceso abierto.
Los autores que publican en esta revista están de acuerdo con los siguientes términos: Licencia Creative Commons Atribución-NoComercial permite que el beneficiario de la licencia tenga el derecho de copiar, distribuir, exhibir y representar la obra y hacer obras derivadas para fines no comerciales siempre y cuando reconozca y cite la obra de la forma especificada por el autor o el licenciante. Los autores pueden establecer por separado acuerdos adicionales para la distribución no exclusiva de la versión de la obra publicada en la revista (por ejemplo, situarlo en un repositorio institucional o publicarlo en un libro), con un reconocimiento de su publicación inicial en esta revista. Se permite y se anima a los autores a difundir sus trabajos electrónicamente (por ejemplo, en repositorios institucionales o en su propio sitio web) antes y durante el proceso de envío, ya que puede dar lugar a intercambios productivos, así como a una citación más temprana y mayor de los trabajos publicados (Véase The Effect of Open Access) (en inglés). Lo anterior debe realizarse siempre sobre el artículo ya publicado por Ciencia & Futuro.
Los autores mantienen el control sobre la integridad de sus trabajos y el derecho a ser adecuadamente reconocidos y citados.
A los editores se les otorgan derechos no exclusivos para publicar y distribuir.